Beverage-Air 412-118D-01 Genuine OEM Drawer Slide Assembly – Replaces 403-843D-01

Beverage-Air 412-118D-01 Genuine OEM Drawer Slide Assembly – Replaces 403-843D-01

The Beverage-Air 412-118D-01 is a Genuine OEM drawer slide assembly designed for compatible Beverage-Air commercial refrigeration equipment. This current slide-rail assembly replaces former Beverage-Air manufacturer part number 403-843D-01.

Beverage-Air identifies the 412-118D-01 as a Fulterer 400 mm left- and right-hand slide assembly used in compatible URC, WTR, and SPD refrigeration equipment. The approximately 400 mm slide length corresponds to roughly 15-3/4 inches.

Use Beverage-Air manufacturer part number 412-118D-01 as the current primary identification reference. Customers replacing an older assembly marked 403-843D-01 should also compare the equipment model, serial number, slide configuration, mounting points, and original drawer hardware before ordering.

Product Details

• Manufacturer: Beverage-Air
• Current Manufacturer Part Number / MPN: 412-118D-01
• Former Manufacturer Part Number: 403-843D-01
• Part Type: Drawer Slide / Slide Rail Assembly
• Classification: Genuine OEM
• Slide Manufacturer / Style: Fulterer
• Nominal Length: 400 mm / approximately 15-3/4"
• Configuration: Left- and Right-Hand Slide Assembly
• Application Families: URC / WTR / SPD
• Application: Commercial Refrigeration Drawer Equipment

What the Beverage-Air Drawer Slide Assembly Does

The drawer slide assembly supports the refrigerated drawer as it opens and closes. The slide rails guide the drawer through its intended travel while helping maintain proper alignment within the cabinet.

Correctly operating slides allow the drawer to move smoothly, remain supported during use, and return to its proper closed position. Drawer alignment is also important because a sagging or improperly positioned drawer can prevent the gasket from making consistent contact with the cabinet.

Current 412-118D-01 Replaces 403-843D-01

The former Beverage-Air 403-843D-01 drawer-slide set has been superseded by 412-118D-01. Current OEM parts documentation lists 412-118D-01 as the replacement slide rail assembly.

If the original equipment or previous service documentation lists 403-843D-01, use the equipment model and serial number to confirm the current 412-118D-01 replacement before ordering.

400 mm / 15-3/4" Slide Configuration

Beverage-Air identifies the current slide assembly as a 400 mm Fulterer slide. The previous 403-843D-01 assembly is commonly cataloged at approximately 15-3/4" long x 2-3/8".

Do not select a drawer slide by length alone. Rail profile, mounting arrangement, left/right configuration, locking hardware, drawer design, and equipment application should also match.

Left- and Right-Hand Slide Assembly

The current Beverage-Air 412-118D-01 configuration is identified as an LH and RH slide assembly. This provides the drawer-supporting slide components required for the applicable left and right sides of the drawer system.

Before installation, compare all supplied components with the existing rails and confirm the mounting locations and orientation.

Drawer Locking Mechanism

Beverage-Air drawer systems use slide assemblies with locking features that help prevent the drawer from separating from the cabinet during normal opening and closing.

When servicing these drawers, the locking tabs and sliding members should be inspected along with the rails. A drawer that will not remove, reinstall, or travel correctly may have a locking-tab or alignment issue rather than a failed rail alone.

Common Signs Drawer Slides May Need Replacement

• Drawer is difficult to open or close
• Drawer sticks during travel
• Drawer sags or sits unevenly
• Excessive side-to-side movement develops
• Slide rails are bent or physically damaged
• Bearings or internal slide components bind
• Drawer does not fully close
• Locking tabs or slide members are damaged
• Drawer gasket no longer contacts the cabinet evenly because of alignment problems

These symptoms do not automatically mean the slide assembly is the only problem. Drawer frames, locking tabs, mounting rails, cabinet hardware, gaskets, and drawer alignment should also be inspected.

Technician Service Information

Before replacing the slide assembly, remove the drawer according to the equipment service procedure and inspect both sides of the drawer system.

Check:

• Left- and right-hand slide rails
• Locking tabs
• Sliding members
• Mounting hardware
• Drawer frame condition
• Cabinet mounting points
• Drawer alignment
• Gasket contact after the drawer is closed

After installation, move the drawer through its complete travel several times. Confirm smooth extension and retraction, proper locking, correct alignment, and consistent gasket contact with the cabinet.

Before You Order

Confirm Beverage-Air manufacturer part number 412-118D-01 or the former 403-843D-01 reference before ordering.

Verify the following:

• Current Beverage-Air part number 412-118D-01
• Former 403-843D-01 reference when applicable
• Approximately 400 mm / 15-3/4" slide configuration
• Equipment model number
• Equipment serial number
• Left- and right-hand rail configuration
• Original mounting points
• Drawer frame and locking-tab arrangement
• Original slide profile and hardware

Do not substitute another drawer slide based only on overall length or appearance. Commercial refrigeration slides can use different rail profiles, locking systems, mounting locations, and load configurations.

Frequently Asked Questions

What is Beverage-Air part number 412-118D-01?
Beverage-Air 412-118D-01 is a Genuine OEM Fulterer drawer slide rail assembly used in compatible Beverage-Air commercial refrigeration equipment.

Does 412-118D-01 replace Beverage-Air 403-843D-01?
Yes. Current OEM parts catalogs identify 403-843D-01 as obsolete and replaced by 412-118D-01.

How long is the Beverage-Air drawer slide?
The current 412-118D-01 assembly is identified as a 400 mm slide, which is approximately 15-3/4 inches long.

Does the assembly include left- and right-hand slides?
Beverage-Air's current parts documentation identifies 412-118D-01 as an LH and RH slide assembly.

What equipment families use 412-118D-01?
Beverage-Air's current parts list associates the assembly with URC, WTR, and SPD equipment families. Verify the exact equipment model and serial number before ordering.

Why is my Beverage-Air drawer difficult to open?
Possible causes include bent or worn slides, damaged locking tabs, drawer misalignment, damaged mounting hardware, contamination in the slide mechanism, or a problem with the drawer frame.

Can damaged drawer slides affect gasket sealing?
Yes. Worn or misaligned slides can allow the drawer to sag or sit incorrectly, which may prevent the gasket from making even contact with the cabinet.

How do I confirm this is the correct replacement?
Match 412-118D-01 or the former 403-843D-01 reference and verify the equipment model, serial number, slide length, left/right configuration, mounting points, and original drawer hardware before ordering.

Beverage-Air Commercial Refrigeration Drawer Hardware

The Beverage-Air 412-118D-01 slide assembly is designed for commercial refrigeration drawer applications requiring the specified Fulterer 400 mm rail configuration. Accurate manufacturer part-number, equipment, rail, and mounting identification helps reduce incorrect orders and supports smooth refrigerated drawer operation.