{"title":"Leer Commercial Parts","description":"\u003cp\u003eBrowse available Leer parts listed by PartsDirectOnline. Before ordering, compare the complete manufacturer part number and equipment model information with your original component. If you are unsure which part fits, contact us with the model and serial number.\u003c\/p\u003e","products":[{"product_id":"leer-736-013-magnetic-door-gasket","title":"Leer 736-013 OEM Magnetic Door Gasket","description":"\u003ch2\u003eLeer 736-013 OEM Magnetic Door Gasket\u003c\/h2\u003e\n\n\u003cp\u003eThe \u003cstrong\u003eLeer 736-013 Magnetic Door Gasket\u003c\/strong\u003e is an OEM replacement door seal designed for compatible Leer commercial walk-in cooler and freezer applications. Installed around the door perimeter, the gasket helps create a dependable seal between the refrigerated door and frame to reduce unwanted infiltration of warm, moisture-laden ambient air.\u003c\/p\u003e\n\n\u003cp\u003eA properly sealing gasket is critical to commercial refrigeration performance. A worn, torn, hardened, compressed, loose, or damaged gasket can allow outside air into the refrigerated space and may contribute to condensation, frost accumulation, longer refrigeration run times, reduced temperature stability, and excessive energy use.\u003c\/p\u003e\n\n\u003cp\u003eWhen inspection confirms the original door gasket requires replacement, using the correct \u003cstrong\u003eLeer OEM 736-013\u003c\/strong\u003e helps restore the door-sealing configuration intended for compatible Leer refrigeration equipment.\u003c\/p\u003e\n\n\u003ch2\u003eOEM Part Details\u003c\/h2\u003e\n\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Leer\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOEM Part Number:\u003c\/strong\u003e 736-013\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMPN:\u003c\/strong\u003e 736-013\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSKU:\u003c\/strong\u003e 736-013\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart Type:\u003c\/strong\u003e Magnetic Door Gasket\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eApplication:\u003c\/strong\u003e Commercial Walk-In Cooler \u0026amp; Freezer Doors\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSystem:\u003c\/strong\u003e Refrigerated Door Sealing System\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFunction:\u003c\/strong\u003e Magnetic Door-to-Frame Seal\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eWhat the Leer 736-013 Door Gasket Does\u003c\/h2\u003e\n\n\u003cp\u003eThe \u003cstrong\u003eLeer 736-013 gasket\u003c\/strong\u003e forms the primary sealing surface between the refrigerated door and cabinet or walk-in frame. When the door closes, the magnetic gasket helps maintain consistent contact with the mating surface to limit air leakage and moisture infiltration.\u003c\/p\u003e\n\n\u003cp\u003eProper gasket condition helps support:\u003c\/p\u003e\n\n\u003cul\u003e\n\u003cli\u003eConsistent refrigerated-space temperatures\u003c\/li\u003e\n\u003cli\u003eReduced warm-air infiltration\u003c\/li\u003e\n\u003cli\u003eReduced moisture entering the cooler or freezer\u003c\/li\u003e\n\u003cli\u003eProper door-to-frame sealing\u003c\/li\u003e\n\u003cli\u003eReduced condensation around the opening\u003c\/li\u003e\n\u003cli\u003eReduced frost and ice accumulation\u003c\/li\u003e\n\u003cli\u003eNormal refrigeration-system run time\u003c\/li\u003e\n\u003cli\u003eDependable commercial refrigeration operation\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eCommon Signs of a Worn Door Gasket\u003c\/h2\u003e\n\n\u003cp\u003eCommercial refrigeration technicians and facility personnel may inspect the Leer 736-013 when experiencing conditions such as:\u003c\/p\u003e\n\n\u003cul\u003e\n\u003cli\u003eVisible gaps around the closed door\u003c\/li\u003e\n\u003cli\u003eGasket is cracked, torn, or split\u003c\/li\u003e\n\u003cli\u003eGasket has hardened and no longer compresses normally\u003c\/li\u003e\n\u003cli\u003eMagnetic seal no longer pulls evenly against the frame\u003c\/li\u003e\n\u003cli\u003eGasket corners are damaged\u003c\/li\u003e\n\u003cli\u003eGasket has pulled away from its mounting channel\u003c\/li\u003e\n\u003cli\u003eCondensation forms around the door opening\u003c\/li\u003e\n\u003cli\u003eFrost or ice develops near the gasket\u003c\/li\u003e\n\u003cli\u003eDoor requires unusual pressure to seal\u003c\/li\u003e\n\u003cli\u003eRefrigerated temperature becomes less stable\u003c\/li\u003e\n\u003cli\u003eRefrigeration equipment runs longer than expected\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eThese symptoms do not automatically mean the gasket is the only problem. Door alignment, hinges, closers, latches, strikes, frame condition, and refrigeration-system performance should also be inspected when sealing problems are present.\u003c\/p\u003e\n\n\u003ch2\u003eWhy Magnetic Gasket Condition Matters\u003c\/h2\u003e\n\n\u003cp\u003eA magnetic refrigeration gasket is designed to maintain contact with the door frame when the door is closed. If the gasket loses its shape, magnetic holding ability, or mounting integrity, the seal may become uneven around the perimeter.\u003c\/p\u003e\n\n\u003cp\u003eAir leakage around a walk-in cooler or freezer door can contribute to:\u003c\/p\u003e\n\n\u003cul\u003e\n\u003cli\u003eHigher refrigeration load\u003c\/li\u003e\n\u003cli\u003eLonger compressor run times\u003c\/li\u003e\n\u003cli\u003eMoisture infiltration\u003c\/li\u003e\n\u003cli\u003eCondensation\u003c\/li\u003e\n\u003cli\u003eFrost or ice formation\u003c\/li\u003e\n\u003cli\u003eSlower temperature recovery\u003c\/li\u003e\n\u003cli\u003eIncreased wear on refrigeration components\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eCheck Door Alignment Before Replacing the Gasket\u003c\/h2\u003e\n\n\u003cp\u003eA new gasket cannot correct every door-sealing problem. Before replacing the Leer 736-013, inspect the complete door assembly to confirm that the door closes squarely against the frame.\u003c\/p\u003e\n\n\u003cp\u003eTechnicians should inspect:\u003c\/p\u003e\n\n\u003cul\u003e\n\u003cli\u003eDoor alignment\u003c\/li\u003e\n\u003cli\u003eHinge condition\u003c\/li\u003e\n\u003cli\u003eLoose hinge hardware\u003c\/li\u003e\n\u003cli\u003eDoor sag\u003c\/li\u003e\n\u003cli\u003eDoor closer operation\u003c\/li\u003e\n\u003cli\u003eLatch and strike alignment\u003c\/li\u003e\n\u003cli\u003eFrame condition\u003c\/li\u003e\n\u003cli\u003eGasket mounting channel\u003c\/li\u003e\n\u003cli\u003eDoor panel condition\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eCorrecting alignment or hardware problems before installing the replacement gasket can help provide more even compression and a more reliable seal.\u003c\/p\u003e\n\n\u003ch2\u003eInspect the Gasket Mounting Area\u003c\/h2\u003e\n\n\u003cp\u003eBefore installing the replacement gasket, inspect the retaining channel or mounting area for conditions that may prevent proper seating.\u003c\/p\u003e\n\n\u003cp\u003eLook for:\u003c\/p\u003e\n\n\u003cul\u003e\n\u003cli\u003eDirt or grease buildup\u003c\/li\u003e\n\u003cli\u003eFood residue\u003c\/li\u003e\n\u003cli\u003eDamaged retaining surfaces\u003c\/li\u003e\n\u003cli\u003eBent or distorted mounting areas\u003c\/li\u003e\n\u003cli\u003eCorrosion\u003c\/li\u003e\n\u003cli\u003eLoose retainers\u003c\/li\u003e\n\u003cli\u003eOld adhesive or debris where applicable\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eThe replacement gasket should seat evenly around the complete door perimeter.\u003c\/p\u003e\n\n\u003ch2\u003eHow to Check the Door Seal\u003c\/h2\u003e\n\n\u003cp\u003eWith the door closed, inspect the gasket around the entire perimeter. The gasket should maintain reasonably even contact with the frame without obvious gaps, folded areas, or sections that fail to compress.\u003c\/p\u003e\n\n\u003cp\u003ePay particular attention to:\u003c\/p\u003e\n\n\u003cul\u003e\n\u003cli\u003eUpper corners\u003c\/li\u003e\n\u003cli\u003eLower corners\u003c\/li\u003e\n\u003cli\u003eHinge side\u003c\/li\u003e\n\u003cli\u003eLatch side\u003c\/li\u003e\n\u003cli\u003eBottom sealing area\u003c\/li\u003e\n\u003cli\u003eSections showing condensation or frost\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eIf one section does not contact the frame properly, determine whether the problem is the gasket itself or the door alignment before replacing additional components.\u003c\/p\u003e\n\n\u003ch2\u003eTechnician Checks Before Ordering\u003c\/h2\u003e\n\n\u003cp\u003eBefore ordering the Leer 736-013 magnetic door gasket, verify:\u003c\/p\u003e\n\n\u003cul\u003e\n\u003cli\u003eOEM part number \u003cstrong\u003e736-013\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003eComplete Leer equipment or door model\u003c\/li\u003e\n\u003cli\u003eEquipment serial number where available\u003c\/li\u003e\n\u003cli\u003eOriginal gasket profile\u003c\/li\u003e\n\u003cli\u003eOverall gasket dimensions\u003c\/li\u003e\n\u003cli\u003eMagnetic gasket configuration\u003c\/li\u003e\n\u003cli\u003eMounting style\u003c\/li\u003e\n\u003cli\u003eDoor orientation\u003c\/li\u003e\n\u003cli\u003eGasket retaining channel\u003c\/li\u003e\n\u003cli\u003eDoor alignment\u003c\/li\u003e\n\u003cli\u003eHinge and closer condition\u003c\/li\u003e\n\u003cli\u003eFrame sealing surface\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003e\u003cstrong\u003eOEM part-number verification should be the primary identification method.\u003c\/strong\u003e Commercial refrigeration gaskets can look similar while having different dimensions, profiles, magnetic arrangements, mounting styles, and door applications.\u003c\/p\u003e\n\n\u003ch2\u003eCommercial Walk-In Cooler \u0026amp; Freezer Applications\u003c\/h2\u003e\n\n\u003cp\u003eLeer commercial refrigeration doors are commonly used in demanding foodservice and cold-storage environments including:\u003c\/p\u003e\n\n\u003cul\u003e\n\u003cli\u003eWalk-in coolers\u003c\/li\u003e\n\u003cli\u003eWalk-in freezers\u003c\/li\u003e\n\u003cli\u003eConvenience stores\u003c\/li\u003e\n\u003cli\u003eSupermarkets\u003c\/li\u003e\n\u003cli\u003eRestaurants\u003c\/li\u003e\n\u003cli\u003eCommercial kitchens\u003c\/li\u003e\n\u003cli\u003eHotels\u003c\/li\u003e\n\u003cli\u003eSchools\u003c\/li\u003e\n\u003cli\u003eHospitals\u003c\/li\u003e\n\u003cli\u003eInstitutional kitchens\u003c\/li\u003e\n\u003cli\u003eCold-storage facilities\u003c\/li\u003e\n\u003cli\u003eCommercial foodservice operations\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eInstallation \u0026amp; Service Notes\u003c\/h2\u003e\n\n\u003cp\u003eBefore removing the original gasket, document how it is mounted and note the orientation of the gasket profile and corners.\u003c\/p\u003e\n\n\u003cp\u003eRemove the worn gasket carefully and clean the mounting area before installing the replacement. Make sure the new \u003cstrong\u003eLeer 736-013\u003c\/strong\u003e is seated evenly around the door perimeter.\u003c\/p\u003e\n\n\u003cp\u003eAfter installation:\u003c\/p\u003e\n\n\u003cul\u003e\n\u003cli\u003eClose the door and inspect the complete perimeter\u003c\/li\u003e\n\u003cli\u003eVerify even magnetic contact with the frame\u003c\/li\u003e\n\u003cli\u003eCheck the corners for proper seating\u003c\/li\u003e\n\u003cli\u003eOpen and close the door several times\u003c\/li\u003e\n\u003cli\u003eConfirm the gasket remains fully seated\u003c\/li\u003e\n\u003cli\u003eVerify the door closes without binding\u003c\/li\u003e\n\u003cli\u003eInspect for remaining gaps or air leakage\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eIf sealing problems remain after installation, inspect the hinges, closer, latch, door alignment, and frame condition before assuming the replacement gasket is defective.\u003c\/p\u003e\n\n\u003ch2\u003eWhy Correct Leer OEM Gasket Identification Matters\u003c\/h2\u003e\n\n\u003cp\u003eCommercial walk-in door gaskets can appear nearly identical while having different dimensions, magnetic profiles, mounting arrangements, corner construction, and door applications.\u003c\/p\u003e\n\n\u003cp\u003eUsing \u003cstrong\u003eLeer OEM part number 736-013\u003c\/strong\u003e as the primary identification reference helps technicians and purchasing departments select the intended replacement rather than relying solely on appearance.\u003c\/p\u003e\n\n\u003cp\u003eAlways verify the complete door or equipment model, serial number where available, original gasket profile, dimensions, and mounting arrangement before ordering.\u003c\/p\u003e\n\n\u003ch2\u003eFrequently Asked Questions\u003c\/h2\u003e\n\n\u003ch3\u003eWhat is Leer 736-013?\u003c\/h3\u003e\n\u003cp\u003eLeer 736-013 is an OEM magnetic door gasket used in compatible Leer commercial walk-in cooler and freezer door applications.\u003c\/p\u003e\n\n\u003ch3\u003eWhat does a magnetic walk-in door gasket do?\u003c\/h3\u003e\n\u003cp\u003eThe gasket helps seal the refrigerated door against the frame to reduce warm-air and moisture infiltration.\u003c\/p\u003e\n\n\u003ch3\u003eCan a bad Leer door gasket cause a cooler to run warm?\u003c\/h3\u003e\n\u003cp\u003eYes. Air leakage around a damaged gasket can increase refrigeration load and make temperature control more difficult.\u003c\/p\u003e\n\n\u003ch3\u003eCan a damaged gasket cause condensation?\u003c\/h3\u003e\n\u003cp\u003eYes. Warm, humid air entering through an incomplete seal can contribute to condensation around the door opening.\u003c\/p\u003e\n\n\u003ch3\u003eCan a bad gasket cause frost around a freezer door?\u003c\/h3\u003e\n\u003cp\u003eYes. Moisture entering through a poor seal can freeze and contribute to frost or ice accumulation in low-temperature applications.\u003c\/p\u003e\n\n\u003ch3\u003eWhy is my new gasket not sealing evenly?\u003c\/h3\u003e\n\u003cp\u003ePossible causes include improper installation, door sag, worn hinges, closer problems, latch misalignment, frame damage, or an incorrect gasket profile.\u003c\/p\u003e\n\n\u003ch3\u003eShould I inspect the hinges when replacing Leer 736-013?\u003c\/h3\u003e\n\u003cp\u003eYes. Worn or loose hinges can create uneven gasket compression and prevent the door from sealing correctly.\u003c\/p\u003e\n\n\u003ch3\u003eCan I replace 736-013 with a gasket that has similar dimensions?\u003c\/h3\u003e\n\u003cp\u003eDimensions alone are not enough. Verify OEM part number \u003cstrong\u003e736-013\u003c\/strong\u003e, profile, magnetic configuration, mounting style, and equipment identification.\u003c\/p\u003e\n\n\u003ch3\u003eHow do I confirm Leer 736-013 is the correct replacement?\u003c\/h3\u003e\n\u003cp\u003eVerify OEM part number \u003cstrong\u003e736-013\u003c\/strong\u003e, the complete Leer equipment or door model, original gasket dimensions, profile, magnetic configuration, and mounting style before ordering.\u003c\/p\u003e\n\n\u003ch3\u003eIs professional installation required?\u003c\/h3\u003e\n\u003cp\u003eMany door gaskets can be mechanically replaced, but qualified commercial refrigeration personnel should inspect the door when alignment, hinge, closer, latch, or frame problems prevent proper sealing.\u003c\/p\u003e\n\n\u003ch2\u003eWhy Buy From Parts Direct Online?\u003c\/h2\u003e\n\n\u003cp\u003eParts Direct Online supplies OEM commercial refrigeration replacement parts for service technicians, contractors, supermarkets, convenience stores, restaurants, hotels, schools, hospitals, institutional kitchens, cold-storage facilities, and commercial foodservice operations throughout the United States. Our focus is helping commercial equipment professionals identify the correct replacement component and minimize costly refrigeration downtime.\u003c\/p\u003e\u003ch2\u003eRelated Parts and Fitment Help\u003c\/h2\u003e\u003cp\u003e\u003ca href=\"\/pages\/leer-parts-authority-hub\"\u003eLeer parts\u003c\/a\u003e · \u003ca href=\"\/collections\/gaskets\"\u003emagnetic door gasket parts\u003c\/a\u003e · \u003ca href=\"\/pages\/contact\"\u003eFitment help\u003c\/a\u003e.\u003c\/p\u003e","brand":"Leer","offers":[{"title":"Default Title","offer_id":48929393017055,"sku":"736-013","price":147.6,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0623\/3047\/0623\/files\/leer-door-gasket-magnetic-walk-in-cooler-freezer-replacement-seal-oem-replacement-part-partsdirectonline-1736578.jpg?v=1793841783"},{"product_id":"leer-736-023-38-inch-door-sweep","title":"Leer 736-023 OEM 38\" Walk-In Cooler \u0026 Freezer Door Sweep","description":"\u003cp data-pdo-fitment-help=\"2026-10-24\"\u003e\u003cstrong\u003eConfirm fit before ordering:\u003c\/strong\u003e \u003ca href=\"tel:+16318730509\"\u003eCall 631-873-0509\u003c\/a\u003e or \u003ca href=\"mailto:jmatos@partsdirectonline.com?subject=Part%20fitment%20check\"\u003eemail the product name, equipment model, serial number and part photos\u003c\/a\u003e.\u003c\/p\u003e\u003ch2\u003eLeer 736-023 OEM 38\" Walk-In Cooler \u0026amp; Freezer Door Sweep\u003c\/h2\u003e\n\n\u003cp\u003eThe \u003cstrong\u003eLeer 736-023 Door Sweep\u003c\/strong\u003e is an OEM 38-inch bottom door seal designed for compatible Leer commercial walk-in cooler and freezer applications. Installed along the bottom edge of the refrigerated door, the sweep helps close the gap between the door and threshold area to reduce unwanted infiltration of warm, moisture-laden ambient air.\u003c\/p\u003e\n\n\u003cp\u003eA properly sealing bottom sweep is important to commercial refrigeration performance because air leakage beneath a walk-in door can contribute to condensation, frost, ice accumulation, temperature instability, and increased refrigeration-system run time. A sweep that becomes torn, flattened, hardened, loose, distorted, or physically damaged may no longer maintain consistent contact with the floor or threshold.\u003c\/p\u003e\n\n\u003cp\u003eWhen inspection confirms the original bottom seal requires replacement, using the correct \u003cstrong\u003eLeer OEM 736-023\u003c\/strong\u003e helps restore the lower door-sealing configuration intended for compatible Leer refrigeration equipment.\u003c\/p\u003e\n\n\u003ch2\u003eOEM Part Details \u0026amp; Dimensions\u003c\/h2\u003e\n\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Leer\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOEM Part Number:\u003c\/strong\u003e 736-023\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMPN:\u003c\/strong\u003e 736-023\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSKU:\u003c\/strong\u003e 736-023\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePart Type:\u003c\/strong\u003e Door Sweep \/ Bottom Door Seal\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLength:\u003c\/strong\u003e 38\"\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eApplication:\u003c\/strong\u003e Commercial Walk-In Cooler \u0026amp; Freezer Doors\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSystem:\u003c\/strong\u003e Refrigerated Door Sealing System\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFunction:\u003c\/strong\u003e Lower Door-to-Threshold Seal\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eWhat the Leer 736-023 Door Sweep Does\u003c\/h2\u003e\n\n\u003cp\u003eThe \u003cstrong\u003eLeer 736-023 bottom door sweep\u003c\/strong\u003e seals the lower portion of the walk-in door where a conventional perimeter gasket may not provide coverage. When the door closes, the sweep helps maintain contact with the applicable floor, sill, or threshold area and reduces the open gap beneath the door.\u003c\/p\u003e\n\n\u003cp\u003eProper bottom-door sealing helps support:\u003c\/p\u003e\n\n\u003cul\u003e\n\u003cli\u003eReduced warm-air infiltration\u003c\/li\u003e\n\u003cli\u003eReduced moisture entering the refrigerated space\u003c\/li\u003e\n\u003cli\u003eMore stable walk-in cooler or freezer temperatures\u003c\/li\u003e\n\u003cli\u003eReduced condensation around the doorway\u003c\/li\u003e\n\u003cli\u003eReduced frost and ice accumulation\u003c\/li\u003e\n\u003cli\u003eImproved door sealing\u003c\/li\u003e\n\u003cli\u003eReduced unnecessary refrigeration-system load\u003c\/li\u003e\n\u003cli\u003eDependable commercial refrigeration operation\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003e38-Inch Leer Bottom Door Seal\u003c\/h2\u003e\n\n\u003cp\u003eThis listing is identified as a \u003cstrong\u003e38-inch Leer door sweep\u003c\/strong\u003e. Length is an important replacement specification, but overall length alone should not be used to determine compatibility.\u003c\/p\u003e\n\n\u003cp\u003eBefore ordering, compare:\u003c\/p\u003e\n\n\u003cul\u003e\n\u003cli\u003eOEM part number \u003cstrong\u003e736-023\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e38-inch length\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003eOriginal sweep profile\u003c\/li\u003e\n\u003cli\u003eMounting arrangement\u003c\/li\u003e\n\u003cli\u003eDoor width and configuration\u003c\/li\u003e\n\u003cli\u003eLeer equipment or door identification\u003c\/li\u003e\n\u003cli\u003eSerial information where available\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eCommon Signs of a Worn Door Sweep\u003c\/h2\u003e\n\n\u003cp\u003eCommercial refrigeration technicians and facility personnel may inspect the Leer 736-023 when experiencing conditions such as:\u003c\/p\u003e\n\n\u003cul\u003e\n\u003cli\u003eVisible gap beneath the closed door\u003c\/li\u003e\n\u003cli\u003eWarm air entering under the door\u003c\/li\u003e\n\u003cli\u003eSweep is torn or split\u003c\/li\u003e\n\u003cli\u003eBottom seal is flattened or permanently compressed\u003c\/li\u003e\n\u003cli\u003eSweep has hardened and no longer conforms to the threshold\u003c\/li\u003e\n\u003cli\u003eSweep has pulled away from the door\u003c\/li\u003e\n\u003cli\u003eBottom edge is uneven or distorted\u003c\/li\u003e\n\u003cli\u003eCondensation develops around the lower doorway\u003c\/li\u003e\n\u003cli\u003eFrost or ice forms near the threshold\u003c\/li\u003e\n\u003cli\u003eWalk-in temperature becomes more difficult to maintain\u003c\/li\u003e\n\u003cli\u003eRefrigeration equipment runs longer than normal\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eThese symptoms do not automatically mean the door sweep is the only problem. Door alignment, hinges, closers, thresholds, floor condition, perimeter gaskets, latches, and frame condition should also be inspected when a walk-in door does not seal correctly.\u003c\/p\u003e\n\n\u003ch2\u003eWhy the Bottom Door Seal Matters\u003c\/h2\u003e\n\n\u003cp\u003eThe bottom of a walk-in cooler or freezer door is particularly vulnerable to air leakage because the seal must maintain contact while still allowing the door to open and close normally. Repeated use can wear or deform the sweep over time.\u003c\/p\u003e\n\n\u003cp\u003eExcessive air infiltration beneath the door can contribute to:\u003c\/p\u003e\n\n\u003cul\u003e\n\u003cli\u003eLonger refrigeration run times\u003c\/li\u003e\n\u003cli\u003eSlower temperature recovery\u003c\/li\u003e\n\u003cli\u003eMoisture entering the refrigerated space\u003c\/li\u003e\n\u003cli\u003eCondensation\u003c\/li\u003e\n\u003cli\u003eFrost or ice buildup\u003c\/li\u003e\n\u003cli\u003eAdditional load on refrigeration equipment\u003c\/li\u003e\n\u003cli\u003eReduced temperature stability\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eDoor Sweep vs. Perimeter Door Gasket\u003c\/h2\u003e\n\n\u003cp\u003eThe bottom door sweep and magnetic perimeter gasket perform related but different sealing functions.\u003c\/p\u003e\n\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eDoor Sweep:\u003c\/strong\u003e Seals the lower edge of the door against the threshold or floor area.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePerimeter Gasket:\u003c\/strong\u003e Seals the sides and upper portion of the door against the frame.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eWhen air leakage is present, both sealing systems should be inspected. Replacing the bottom sweep will not correct a damaged perimeter gasket, and replacing the perimeter gasket will not correct an open gap beneath the door.\u003c\/p\u003e\n\n\u003ch2\u003eCheck Door Alignment Before Replacing the Sweep\u003c\/h2\u003e\n\n\u003cp\u003eA new bottom sweep cannot compensate for every door-alignment problem. Before replacing the Leer 736-023, inspect the complete door assembly to determine whether the door is sitting at the correct height and closing squarely.\u003c\/p\u003e\n\n\u003cp\u003eTechnicians should inspect:\u003c\/p\u003e\n\n\u003cul\u003e\n\u003cli\u003eDoor alignment\u003c\/li\u003e\n\u003cli\u003eDoor height\u003c\/li\u003e\n\u003cli\u003eHinge condition\u003c\/li\u003e\n\u003cli\u003eLoose hinge hardware\u003c\/li\u003e\n\u003cli\u003eDoor sag\u003c\/li\u003e\n\u003cli\u003eDoor closer operation\u003c\/li\u003e\n\u003cli\u003eLatch and strike alignment\u003c\/li\u003e\n\u003cli\u003eThreshold condition\u003c\/li\u003e\n\u003cli\u003eFloor condition\u003c\/li\u003e\n\u003cli\u003ePerimeter door gasket\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eA sagging or misaligned door can cause excessive sweep wear or prevent consistent contact with the threshold.\u003c\/p\u003e\n\n\u003ch2\u003eInspect the Threshold \u0026amp; Floor Area\u003c\/h2\u003e\n\n\u003cp\u003eA new sweep should make appropriate contact with the surface beneath the door. Damage or irregularities in the threshold or floor can affect sealing even when the replacement sweep is correct.\u003c\/p\u003e\n\n\u003cp\u003eInspect for:\u003c\/p\u003e\n\n\u003cul\u003e\n\u003cli\u003eDamaged threshold\u003c\/li\u003e\n\u003cli\u003eUneven floor surface\u003c\/li\u003e\n\u003cli\u003eIce accumulation\u003c\/li\u003e\n\u003cli\u003eDebris\u003c\/li\u003e\n\u003cli\u003eLoose threshold hardware\u003c\/li\u003e\n\u003cli\u003ePhysical impact damage\u003c\/li\u003e\n\u003cli\u003eExcessive gap beneath the door\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eTechnician Checks Before Ordering\u003c\/h2\u003e\n\n\u003cp\u003eBefore ordering the Leer 736-023 door sweep, verify:\u003c\/p\u003e\n\n\u003cul\u003e\n\u003cli\u003eOEM part number \u003cstrong\u003e736-023\u003c\/strong\u003e\n\u003c\/li\u003e\n\u003cli\u003e\u003cstrong\u003e38-inch length\u003c\/strong\u003e\u003c\/li\u003e\n\u003cli\u003eComplete Leer equipment or door model\u003c\/li\u003e\n\u003cli\u003eSerial number where available\u003c\/li\u003e\n\u003cli\u003eOriginal sweep profile\u003c\/li\u003e\n\u003cli\u003eMounting style\u003c\/li\u003e\n\u003cli\u003eDoor width\u003c\/li\u003e\n\u003cli\u003eDoor orientation\u003c\/li\u003e\n\u003cli\u003eThreshold configuration\u003c\/li\u003e\n\u003cli\u003eDoor alignment\u003c\/li\u003e\n\u003cli\u003eHinge and closer condition\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003e\u003cstrong\u003eOEM part number, dimensions, and profile should be primary identification points.\u003c\/strong\u003e Commercial walk-in door sweeps can look similar while having different lengths, profiles, mounting arrangements, and door applications.\u003c\/p\u003e\n\n\u003ch2\u003eCommercial Walk-In Cooler \u0026amp; Freezer Applications\u003c\/h2\u003e\n\n\u003cp\u003eLeer commercial refrigeration doors are commonly installed in demanding cold-storage and foodservice environments including:\u003c\/p\u003e\n\n\u003cul\u003e\n\u003cli\u003eWalk-in coolers\u003c\/li\u003e\n\u003cli\u003eWalk-in freezers\u003c\/li\u003e\n\u003cli\u003eConvenience stores\u003c\/li\u003e\n\u003cli\u003eSupermarkets\u003c\/li\u003e\n\u003cli\u003eRestaurants\u003c\/li\u003e\n\u003cli\u003eCommercial kitchens\u003c\/li\u003e\n\u003cli\u003eHotels\u003c\/li\u003e\n\u003cli\u003eSchools\u003c\/li\u003e\n\u003cli\u003eHospitals\u003c\/li\u003e\n\u003cli\u003eInstitutional kitchens\u003c\/li\u003e\n\u003cli\u003eCold-storage facilities\u003c\/li\u003e\n\u003cli\u003eCommercial foodservice operations\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch2\u003eInstallation \u0026amp; Service Notes\u003c\/h2\u003e\n\n\u003cp\u003eBefore removing the original sweep, document its mounting position, orientation, profile, and relationship to the floor or threshold.\u003c\/p\u003e\n\n\u003cp\u003eRemove the worn bottom seal carefully and clean the mounting area. Compare the replacement \u003cstrong\u003eLeer 736-023\u003c\/strong\u003e with the original component before installation.\u003c\/p\u003e\n\n\u003cp\u003eAfter installation:\u003c\/p\u003e\n\n\u003cul\u003e\n\u003cli\u003eVerify the sweep is mounted securely\u003c\/li\u003e\n\u003cli\u003eConfirm the full 38-inch seal is positioned correctly\u003c\/li\u003e\n\u003cli\u003eClose the door and inspect bottom contact\u003c\/li\u003e\n\u003cli\u003eCheck for visible gaps\u003c\/li\u003e\n\u003cli\u003eOpen and close the door several times\u003c\/li\u003e\n\u003cli\u003eConfirm the sweep does not bind excessively\u003c\/li\u003e\n\u003cli\u003eVerify the door closes normally\u003c\/li\u003e\n\u003cli\u003eInspect for remaining air leakage\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cp\u003eIf a gap remains after installation, inspect the hinges, closer, door alignment, threshold, and overall door height before assuming the replacement sweep is defective.\u003c\/p\u003e\n\n\u003ch2\u003eWhy Correct Leer OEM Door Sweep Identification Matters\u003c\/h2\u003e\n\n\u003cp\u003eCommercial walk-in door sweeps can appear nearly identical while having different lengths, profiles, mounting methods, and equipment applications.\u003c\/p\u003e\n\n\u003cp\u003eUsing \u003cstrong\u003eLeer OEM part number 736-023\u003c\/strong\u003e together with the verified \u003cstrong\u003e38-inch length\u003c\/strong\u003e provides technicians and purchasing departments with strong identification points when comparing the replacement with the original bottom seal.\u003c\/p\u003e\n\n\u003cp\u003eAlways verify the complete door or equipment identification, original sweep profile, dimensions, mounting arrangement, and threshold configuration before ordering.\u003c\/p\u003e\n\n\u003ch2\u003eFrequently Asked Questions\u003c\/h2\u003e\n\n\u003ch3\u003eWhat is Leer 736-023?\u003c\/h3\u003e\n\u003cp\u003eLeer 736-023 is an OEM 38-inch bottom door sweep or lower door seal used in compatible Leer commercial walk-in cooler and freezer applications.\u003c\/p\u003e\n\n\u003ch3\u003eHow long is the Leer 736-023 door sweep?\u003c\/h3\u003e\n\u003cp\u003eThe Leer 736-023 is identified as a \u003cstrong\u003e38-inch door sweep\u003c\/strong\u003e.\u003c\/p\u003e\n\n\u003ch3\u003eIs Leer 736-023 a magnetic door gasket?\u003c\/h3\u003e\n\u003cp\u003eNo. This part is a \u003cstrong\u003ebottom door sweep \/ lower door seal\u003c\/strong\u003e. A magnetic perimeter gasket is a separate door-sealing component.\u003c\/p\u003e\n\n\u003ch3\u003eWhat does a walk-in cooler door sweep do?\u003c\/h3\u003e\n\u003cp\u003eThe sweep helps close the gap between the bottom of the refrigerated door and the floor or threshold to reduce warm-air and moisture infiltration.\u003c\/p\u003e\n\n\u003ch3\u003eCan a bad bottom door sweep cause a walk-in cooler to run warm?\u003c\/h3\u003e\n\u003cp\u003eYes. Significant air leakage beneath the door can increase refrigeration load and make temperature control more difficult.\u003c\/p\u003e\n\n\u003ch3\u003eCan a damaged sweep cause frost around a freezer door?\u003c\/h3\u003e\n\u003cp\u003eYes. Moisture entering through an open bottom gap can contribute to frost or ice accumulation in low-temperature applications.\u003c\/p\u003e\n\n\u003ch3\u003eWhy is there still a gap after installing a new door sweep?\u003c\/h3\u003e\n\u003cp\u003ePossible causes include door sag, worn hinges, incorrect door height, threshold damage, improper installation, or an incorrect sweep profile.\u003c\/p\u003e\n\n\u003ch3\u003eShould I check the hinges when replacing Leer 736-023?\u003c\/h3\u003e\n\u003cp\u003eYes. Door sag caused by worn or loose hinges can create uneven bottom clearance and premature sweep wear.\u003c\/p\u003e\n\n\u003ch3\u003eCan I replace Leer 736-023 with any 38-inch sweep?\u003c\/h3\u003e\n\u003cp\u003eNo. Length alone does not establish compatibility. Verify OEM part number \u003cstrong\u003e736-023\u003c\/strong\u003e, profile, mounting style, door configuration, and dimensions before ordering.\u003c\/p\u003e\n\n\u003ch3\u003eHow do I confirm Leer 736-023 is the correct replacement?\u003c\/h3\u003e\n\u003cp\u003eVerify OEM part number \u003cstrong\u003e736-023\u003c\/strong\u003e, the 38-inch length, original sweep profile, mounting arrangement, Leer door identification, and threshold configuration before ordering.\u003c\/p\u003e\n\n\u003ch3\u003eIs professional installation required?\u003c\/h3\u003e\n\u003cp\u003eMany door sweeps can be mechanically replaced, but qualified commercial refrigeration personnel should inspect the door when alignment, hinge, closer, threshold, or sealing problems prevent proper closure.\u003c\/p\u003e\n\n\u003ch2\u003eWhy Buy From Parts Direct Online?\u003c\/h2\u003e\n\n\u003cp\u003eParts Direct Online supplies OEM commercial refrigeration replacement parts for service technicians, contractors, supermarkets, convenience stores, restaurants, hotels, schools, hospitals, institutional kitchens, cold-storage facilities, and commercial foodservice operations throughout the United States. Our focus is helping commercial equipment professionals identify the correct replacement component and minimize costly refrigeration downtime.\u003c\/p\u003e\u003ch2\u003eRelated Parts and Fitment Help\u003c\/h2\u003e\u003cp\u003e\u003ca href=\"\/pages\/leer-parts-authority-hub\"\u003eLeer parts\u003c\/a\u003e · \u003ca href=\"\/collections\/door-sweeps\"\u003ecommercial walk-in cooler \u0026amp; freezer door sweeps\u003c\/a\u003e · \u003ca href=\"\/pages\/contact\"\u003eFitment help\u003c\/a\u003e.\u003c\/p\u003e","brand":"Leer","offers":[{"title":"Default Title","offer_id":48929473495263,"sku":"736-023","price":66.23,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0623\/3047\/0623\/files\/leer-door-sweep-38-walk-in-cooler-freezer-bottom-seal-replacement-oem-replacement-part-partsdirectonline-2118533.webp?v=1776394218"},{"product_id":"leer-1328023-timer-defrost-plug-in-4-hr","title":"Leer 1328023 Timer, Defrost Plug-In 4 Hr","description":"\u003ch2\u003eLeer 1328023 Defrost Timer\u003c\/h2\u003e\n\u003cp\u003eThe Leer 1328023 is identified as timer, defrost plug-in 4 hr. This component coordinates the defrost cycle in the specified refrigeration control circuit. Match the manufacturer reference to the equipment documentation so the replacement addresses the correct assembly and operating application.\u003c\/p\u003e\n\u003ch3\u003eVerified part identification and specifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eManufacturer reference\u003c\/th\u003e\n\u003ctd\u003eLeer\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eOEM\/MPN\u003c\/th\u003e\n\u003ctd\u003e1328023\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eItem identification\u003c\/th\u003e\n\u003ctd\u003eTimer, Defrost Plug-In 4 Hr\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDocumented catalog weight\u003c\/th\u003e\n\u003ctd\u003e1.0 lb\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eCommercial application and model references\u003c\/h3\u003e\n\u003cp\u003eDocumented equipment model references include 1002UA50MG, 1002UA50MS, 301UA25MG, 401SA25MS, 401UA33MG, 602SA33MS, 602UA45MG, 852UA50MS, IS28A, IS41AG, IS67AG, L040UAGX, L100UASX, LCL170, LP460A, LP460AS, LP610AS, M1000AG, M380, M450AG. Confirm the exact model suffix, serial range and component revision before ordering.\u003c\/p\u003e\n\u003ch3\u003eSymptoms and technician checks\u003c\/h3\u003e\n\u003cp\u003eInspect this component when the equipment shows missing defrost cycles, irregular cycling or a timer that fails to advance. Check timer supply, terminal identification, control wiring and the existing defrost settings before attributing the fault to this part. These symptoms guide diagnosis; they do not establish that replacement is necessary.\u003c\/p\u003e\n\u003cp\u003eA defrost problem may originate at the heater, termination control or wiring. Establish whether the timer is switching correctly before ordering a replacement.\u003c\/p\u003e\n\u003ch3\u003eBefore you order\u003c\/h3\u003e\n\u003cp\u003eUse manufacturer reference 1328023 and compare the item identification above with the removed part. Check the model and serial label, the corresponding parts diagram and any revision or serial break. Confirm the component supplied rather than assuming related brackets, wiring or accessories are included.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eWhat is Leer 1328023?\u003c\/h4\u003e\n\u003cp\u003eIt is identified as timer, defrost plug-in 4 hr. It coordinates the defrost cycle in the specified refrigeration control circuit.\u003c\/p\u003e\n\u003ch4\u003eWhich models are referenced for 1328023?\u003c\/h4\u003e\n\u003cp\u003eDocumented equipment model references include 1002UA50MG, 1002UA50MS, 301UA25MG, 401SA25MS, 401UA33MG, 602SA33MS, 602UA45MG, 852UA50MS, IS28A, IS41AG, IS67AG, L040UAGX, L100UASX, LCL170, LP460A, LP460AS, LP610AS, M1000AG, M380, M450AG. Confirm the exact model suffix, serial range and component revision before ordering.\u003c\/p\u003e\n\u003ch4\u003eWhat specifications distinguish 1328023?\u003c\/h4\u003e\n\u003cp\u003eDocumented catalog weight: 0.16 lb.\u003c\/p\u003e\n\u003ch4\u003eWill a timer with the same number of terminals work?\u003c\/h4\u003e\n\u003cp\u003eTerminal count alone is insufficient. Verify supply voltage, contact arrangement, cycle behavior and the manufacturer part reference.\u003c\/p\u003e\n\u003ch4\u003eWhat should be checked before replacing 1328023?\u003c\/h4\u003e\n\u003cp\u003eCheck timer supply, terminal identification, control wiring and the existing defrost settings. A defrost problem may originate at the heater, termination control or wiring. Establish whether the timer is switching correctly before ordering a replacement.\u003c\/p\u003e\n\u003ch4\u003eWhat information should I provide to confirm 1328023?\u003c\/h4\u003e\n\u003cp\u003eProvide the equipment model and serial number, the number on the removed component and a clear photograph of its connections or mounting. Ask for confirmation of Leer 1328023 against the equipment diagram.\u003c\/p\u003e\n\u003cp\u003eBrowse our \u003ca href=\"\/collections\/all\"\u003ecommercial equipment parts catalog\u003c\/a\u003e for related service components.\u003c\/p\u003e","brand":"Leer","offers":[{"title":"Default Title","offer_id":68019356106975,"sku":"1328023","price":93.58,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0623\/3047\/0623\/files\/leer-1328023-timer-defrost-plug-in-4-hr-oem-replacement-part-partsdirectonline-6143522.jpg?v=1792137485"},{"product_id":"leer-1913014-latch-3-4-to-1-1-2-offset","title":"Leer 1913014 Latch, 3\/4\" To 1-1\/2\" Offset","description":"\u003ch2\u003eLeer 1913014 Door Latch\u003c\/h2\u003e\n\u003cp\u003eThe Leer 1913014 is identified as latch, 3\/4\" to 1-1\/2\" offset. This component performs the latch or strike function identified for the matching commercial door assembly. Match the manufacturer reference to the equipment documentation so the replacement addresses the correct assembly and operating application.\u003c\/p\u003e\n\u003ch3\u003eVerified part identification and specifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eManufacturer reference\u003c\/th\u003e\n\u003ctd\u003eLeer\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eOEM\/MPN\u003c\/th\u003e\n\u003ctd\u003e1913014\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eItem identification\u003c\/th\u003e\n\u003ctd\u003eLatch, 3\/4\" To 1-1\/2\" Offset\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eListed length\/dimension\u003c\/th\u003e\n\u003ctd\u003e4\", 1-1\/2\"\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDocumented catalog weight\u003c\/th\u003e\n\u003ctd\u003e6.0 lb\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eCommercial application and model references\u003c\/h3\u003e\n\u003cp\u003eModel-specific compatibility is not established here. Match this manufacturer reference to your equipment parts diagram and confirm the serial range before ordering.\u003c\/p\u003e\n\u003ch3\u003eSymptoms and technician checks\u003c\/h3\u003e\n\u003cp\u003eInspect this component when the equipment shows poor engagement, worn contact surfaces or broken latch hardware. Check door offset, latch and strike alignment, mounting holes and the component supplied before attributing the fault to this part. These symptoms guide diagnosis; they do not establish that replacement is necessary.\u003c\/p\u003e\n\u003cp\u003eA closing complaint may come from a shifted strike or sagging hinges. Confirm whether you need the latch, a strike or another individual component before ordering.\u003c\/p\u003e\n\u003ch3\u003eBefore you order\u003c\/h3\u003e\n\u003cp\u003eUse manufacturer reference 1913014 and compare the item identification above with the removed part. Check the model and serial label, the corresponding parts diagram and any revision or serial break. Confirm the component supplied rather than assuming related brackets, wiring or accessories are included.\u003c\/p\u003e\n\u003ch3\u003eFrequently asked questions\u003c\/h3\u003e\n\u003ch4\u003eWhat is Leer 1913014?\u003c\/h4\u003e\n\u003cp\u003eIt is identified as latch, 3\/4\" to 1-1\/2\" offset. It performs the latch or strike function identified for the matching commercial door assembly.\u003c\/p\u003e\n\u003ch4\u003eWhich models are referenced for 1913014?\u003c\/h4\u003e\n\u003cp\u003eModel-specific compatibility is not established here. Match this manufacturer reference to your equipment parts diagram and confirm the serial range before ordering.\u003c\/p\u003e\n\u003ch4\u003eWhat specifications distinguish 1913014?\u003c\/h4\u003e\n\u003cp\u003eListed length\/dimension: 4\", 1-1\/2\"; Documented catalog weight: 3.435 lb.\u003c\/p\u003e\n\u003ch4\u003eDoes this listing include every latch component?\u003c\/h4\u003e\n\u003cp\u003eUse the item identification above to determine the component offered. A strike-only listing is not a complete latch; do not assume related hardware is included.\u003c\/p\u003e\n\u003ch4\u003eWhat should be checked before replacing 1913014?\u003c\/h4\u003e\n\u003cp\u003eCheck door offset, latch and strike alignment, mounting holes and the component supplied. A closing complaint may come from a shifted strike or sagging hinges. Confirm whether you need the latch, a strike or another individual component before ordering.\u003c\/p\u003e\n\u003ch4\u003eWhat information should I provide to confirm 1913014?\u003c\/h4\u003e\n\u003cp\u003eProvide the equipment model and serial number, the number on the removed component and a clear photograph of its connections or mounting. Ask for confirmation of Leer 1913014 against the equipment diagram.\u003c\/p\u003e\n\u003cp\u003eBrowse our \u003ca href=\"\/collections\/all\"\u003ecommercial equipment parts catalog\u003c\/a\u003e for related service components.\u003c\/p\u003e","brand":"Leer","offers":[{"title":"Default Title","offer_id":68019356172511,"sku":"1913014","price":206.89,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0623\/3047\/0623\/files\/leer-1913014-latch-3-4-to-1-1-2-offset-product-photo.gif?v=1792018093"}],"url":"https:\/\/partsdirectonline.com\/collections\/leer-commercial-parts.oembed","provider":"PartsDirectonline","version":"1.0","type":"link"}